Rimage AutoPrinter Uživatelská příručka Strana 1

Procházejte online nebo si stáhněte Uživatelská příručka pro Multifunkční zařízení Rimage AutoPrinter. Rimage AutoPrinter User guide Uživatelská příručka

  • Stažení
  • Přidat do mých příruček
  • Tisk
  • Strana
    / 20
  • Tabulka s obsahem
  • KNIHY
  • Hodnocené. / 5. Na základě hodnocení zákazníků
Zobrazit stránku 0
Rimage AutoPrinter™
User Guide
This manual provides the information needed to operate the AutoPrinter and identify the parts.
To setup and install your AutoPrinter, refer to the Setup and Installation Guide included with your
product.
Zobrazit stránku 0
1 2 3 4 5 6 ... 19 20

Shrnutí obsahu

Strany 1 - User Guide

Rimage AutoPrinter™ User Guide This manual provides the information needed to operate the AutoPrinter and identify the parts. To setup and instal

Strany 2

Rimage AutoPrinter 4 110656_H Rear view Printer Control Cable Everest Printer USB Cable Printer Control Cable USB Cable Prism Printer Prism Powe

Strany 3

Operate the AutoPrinter Operate the AutoPrinter Installing the carousel - Important: To prevent errors, the carousel should be installed before opera

Strany 4 - Learn more online

Rimage AutoPrinter 6 110656_H Loading and unloading discs You can load up to 100 discs per carousel bin. You may load discs in the bins before insta

Strany 5 - Contents

Maintain the AutoPrinter Maintain the AutoPrinter Installing ribbons Before installing ribbons in the printer, stop any operations. To change ribbons

Strany 6

Rimage AutoPrinter 8 110656_H 4. Align the printer. a. Slowly slide the lift arm down until the disc just touches the print pad. b. If the disc

Strany 7 - Introduction

Maintain the AutoPrinter Prism printer To align your Prism printer, use the following instructions. # Required tools: • T25 Torx screwdriver • 5/32”

Strany 8 - Front view

Rimage AutoPrinter 10 110656_H b. If the disc is not centered on the print pad, align the printer side to side. i. Using the T25 Torx screwdriver,

Strany 9 - Operator panel

Learn More Learn More AutoPrinter specifications  Note: Specifications for the printer are in the printer user guide. AutoPrinter autoloader, a Rima

Strany 10 - Rear view

Rimage AutoPrinter 12 110656_H n rning is at could result in bodily injury to personnel operating or p e this guideline could result in loss or dam

Strany 11 - Operate the AutoPrinter

Learn More Safety testing Product name: AutoPrinter Model: RAS10 Notice for USA Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. NO

Strany 13 - Maintain the AutoPrinter

Rimage AutoPrinter 14 110656_H Rimage AutoPrinter II Limited One Year Warranty Rimage warrants, to the original end user only, that all non-consumab

Strany 14 - # Tip: Tighten each screw in

Corporate Headquarters: Rimage Corporation 7725 Washington Avenue South Minneapolis, MN 55439 USA 800 553 8312 (toll free US) Service: +1 952 946 00

Strany 15 - # Required tools:

Support information US, Asia/Pacific, Mexico/Latin America Europe Rimage Corporation 7725 Washington Avenue South Minneapolis, MN 55439 USA Attn: Ri

Strany 16 - Rimage AutoPrinter

Contents Contents Introduction ... 1 Operating system requirements

Strany 17 - Learn More

Rimage AutoPrinter™ User Guide . ii

Strany 18 - Safety precautions

Introduction Introduction This manual provides the information needed to operate the AutoPrinter and identify the parts. To setup and install your Au

Strany 19 - Product name: AutoPrinter

Rimage AutoPrinter 2 110656_H Identify the parts of the AutoPrinter Front view Lift Arm Lift Arm Prism Printer Everest Printer Control Panel Cont

Strany 20

Identify the parts of the AutoPrinter Operator panel The operator panel has four indicator lights and an operator button. Operator button Each time y

Komentáře k této Příručce

Žádné komentáře